Unicard - is it possible to get it?
Re: Unicard - is it possible to get it?
Pretty hard to say if it is difficult to make a MZ-80 B port. Despite what some may say, the MZ-80 B hardware is not completely the same as the MZ-80 K series. Unicard is mostly for MZ-700, MZ-800 and MZ-1500 as they share a lot of hardware. For MZ-80 B, there are probably more differences making the firmware too more specific to code. I wish I can access the firmware source so experts can contribute and may extend its functionalities or adapt it for the others like MZ-80 K/MZ-80 A/MZ-1200. And why not a Unicard for the MZ-80 B series as well.
Re: Unicard - is it possible to get it?
Hlide, what you said is true my friend.
I think there is a different approach involving 80B as I the fw already includes FDD support. (there is no eprom on MZ80b floppy card)
I own a MZ80B BUT with no FDD controller and I really like to run CP/M on it!
I had no luck finding an FDD card so far .
I think there is a different approach involving 80B as I the fw already includes FDD support. (there is no eprom on MZ80b floppy card)
I own a MZ80B BUT with no FDD controller and I really like to run CP/M on it!
I had no luck finding an FDD card so far .
member of retroclub.gr (Thessaloniki , Greece)
Re: Unicard - is it possible to get it?
is the schematic and / or PCB layout for the mk3c version available for us MZ-7xx owners?
Some of us might be able to make the hardware for ourselves, since it looks like he original creators are out of time (for now at least).
Some of us might be able to make the hardware for ourselves, since it looks like he original creators are out of time (for now at least).
--
Torfinn
Torfinn
Re: Unicard - is it possible to get it?
I never found the MK3C PCB and as far as I know it is now discarded by using a MK3B PCB and a BUS converter PCB.
Re: Unicard - is it possible to get it?
So, is the schematic for the bus converter available?
Or the difference between the bus on the MZ-700 and the MZ-800?
Or the difference between the bus on the MZ-700 and the MZ-800?
--
Torfinn
Torfinn
Re: Unicard - is it possible to get it?
I don't have the schematics but I think you can easily make this: retrieve the pinout of the male edge connector of MZ-700 and the pinout of the female edge connector of MZ-800. You just need to connect the same pins (A0 -> A0, etc.). You also need to have an external pin to inject the 5V in the MZ-800 side (Unicad is waiting a MZ-800 bus) because it is not present in the MZ-700 side.
Re: Unicard - is it possible to get it?
I see. Are you using the same connectors for both ends? (It looks like that on your picture).
Do you have a part number or a source for these connectors?
Do you have a part number or a source for these connectors?
--
Torfinn
Torfinn
Re: Unicard - is it possible to get it?
I just bought that PCB with two Unicards then solder the components I already had.
Let me check for the components...
Let me check for the components...
Re: Unicard - is it possible to get it?
1 or 2 x Connector ECS50SB1A1-B
1 or 0 x Connector ECR50SB1-B
1 or 0 x Connector ECR50SB1-B
Re: Unicard - is it possible to get it?
In my case, I made it with two ECS50SB1A1-B, because I found too difficult to insert a ECR50SB1-B.